Trench Drain Calculator

When you're making an investment in your property that's as expensive as a trench drain, you deserve to know that the system's going to work when the weather's at its worst. We use your IP address to guess your zip code. From there, we use the NOAA's Atlas 14 data to grab the most accurate rainfall estimate we can in your area, and use the rational method to understand the demands on the trench drain you're installing. We show you all the options that work for the inputted scenario (with a built-in 10% margin), then check the one you select with the EPA's Storm Water Management Model (SWMM).

1Where is the project?

Rainfall loads as soon as we have a ZIP code.

Looking up an approximate ZIP for you. You can type the project ZIP at any time.

Rainfall settings

Use a duration that matches how quickly your site drains. Fifteen minutes is a starting assumption, not a measured travel time. How to choose this

2What drains to the trench?

Only count surfaces that actually drain toward this trench.

3The trench
How does water reach the drain?
4Where does the water leave?

A discharge point is where the channel connects to a drain pipe. More of them can let a smaller, less expensive channel do the job.

Assumptions and site detailsSafety allowance, grades, pipe runs. Sensible defaults are filled in.

Flow

Site

Grate and channel

Drain pipes

Where the water enters

Peak flow to design for— GPM

Enter a ZIP code to size your drain.

Sign in to save this design

Saved designs are tied to your Drainage Connect account, so you can come back to them and we can help with them. Without an account you can still print a quote and add the parts to your cart.

Creating an account opens in a new tab. When you are done, come back here and choose . Your design stays on this page.

Print your design quote

Save this design

Design storms: what a 10-, 25- or 100-year storm means

You’ve probably heard about the concept of a 100-year storm. Does that mean that a storm like this only happens once every 100 years? Unfortunately, that’s not the case. As the US Geological Survey notes in their fantastic article about 100-year floods, most hydrologists don’t love the nomenclature—a 1,000-year storm has a 0.1% chance of occurring in a given year; over the course of a million years, such a storm would be expected to happen 1,000 times. We’ve shown the recurrence intervals and their respective probabilities of occurrence below:

Recurrence intervalAnnual probabilityAt least once in 30 years*

*Using 1 − (1 − 1/T)30, assuming independent years and an unchanged probability. These are statistical estimates, not a forecast. Rainfall recurrence and flood recurrence describe different quantities. USGS explains recurrence intervals ↗

It’s important to remember that these are just probabilities, and events can occur close together. The term “X-year storm” refers to the average long-term recurrence interval, not a guarantee of time between events. So how exactly does it affect us when designing drainage systems?

Impact on drainage system design

When designing a drainage system, it's important to protect critical infrastructure. Hospitals and other critical areas, obviously, should plan for more extreme events than non-critical areas. The appropriate design storm also depends on local requirements, the consequence of flooding, and where water goes if the design storm is exceeded.

As a rule of thumb, we start this calculator with a 25-year storm, with more important and critical infrastructure calling for a review of larger events and local requirements. You can change the setting; it is not a universal code requirement. Your drainage system won’t protect you from a mudslide, and at record precipitation levels, you should be extremely aware of your surroundings.

Calculating runoff with the Rational Method

If you're in the United States, NOAA provides excellent data that's extremely granular about the amount of precipitation that your area may receive in a given timeframe, with a 90% confidence interval. This high quality data serves as the basis for our rainfall lookup, and is used in the calculations for hydrological methods below.

Rainfall depth tells you how much precipitation falls over a period. Rainfall intensity tells you how fast it falls. If a 15-minute storm delivers 1 inch, its average intensity during those 15 minutes is 4 inches per hour. Averaging that inch over a full day would hide the flow your trench needs to handle.

Peak runoff Q = C × i × A × unit conversion

The Rational Method estimates peak runoff using the rainfall intensity for a duration related to the site's time of concentration: how long water takes to reach the design point from the most hydraulically distant part of the contributing area. Only count surfaces that actually drain toward this trench.

Concrete, asphalt, roofs, and lawns do not produce the same runoff. For a mixed site, we add each surface's C × A contribution. With intensity in inches per hour and area in square feet, Q in GPM is i × Σ(C × A) × 0.0103896. Additional inflow and your chosen design allowance are then added explicitly.

The Rational Method supplies a peak rate, not a hydrograph or total storage volume. TR-55 runoff depth calculations can be useful for volume and storage questions, but runoff depth alone cannot determine peak discharge. This calculator uses a transparent Rational Method screen rather than converting a runoff volume into an unsupported peak.

The Rational Method only sets how much water arrives. Every step after it tests whether a drain can carry that flow.

Source: TxDOT Hydraulic Design Manual · Rational Method. Surface defaults are editable assumptions within published ranges.

Trench drain capacity: grate, channel and outlet

It is easy to look at a large grate and assume the drainage system has plenty of capacity. But the grate is only the first step. Water has to enter through the grate, travel along the channel, and leave through an outlet and the pipe beyond it.

01

Peak influent capacity

The rate the grate can admit, at a stated water depth and blockage allowance.

02

Channel capacity

The rate each part of the channel can convey with its geometry, slope, and freeboard.

03

Peak discharge capacity

The rate the outlet connections and downstream pipe can carry away.

Each constraint must be checked against the flow that actually reaches it. Grate capacity across an entire run cannot resolve a local capture problem, and an outlet's capacity cannot help an upstream channel section that is already overloaded.

How we estimate grate capture

At a low point, shallow ponding can make a grate act as a weir. With deeper submergence, the opening behaves more like an orifice. The calculator calculates both and uses the smaller screening capacity at your selected ponding depth:

Weir: Q = 0.37 √(2g) P h3/2
Orifice: Q = Co Aopen √(2gh)

Here P is the effective exterior perimeter in feet, Aopen is the clear opening area in square feet, h is water depth above the grate in feet, and g = 32.2 ft/s². Co defaults to 0.67 for HEC-22 screening; when an NDS grate has a published half-inch-head capacity and opening area, its coefficient is derived from those values (typically about 0.60). The blockage allowance reduces open area and effective perimeter. We do not count every internal grate seam as a new weir.

These low-spot equations do not describe a drain that crosses a slope, where water arrives as a thin moving sheet. If you choose “It flows across a slope”, the calculator uses a different check. The grate’s clear opening has to pass the sheet at its own depth and speed, and full capture is credited only up to 0.025 ft³/s per foot of drain (11.2 GPM per foot). That is the flow at which FHWA’s tests of slotted drains captured all of the water, on slopes from 0.5% to 9%.

Source: FHWA HEC-22, 4th edition · §7.3.1, equations 7.14–7.15 (grates at a low spot) and §7.2.3 (slotted drains in overland flow).

Channel drain flow rate (GPM) and Manning's equation

Manning's equation connects the channel's wetted cross-section with the slope available to move water. A deeper channel can carry more water, but depth alone is not the answer: roughness, the shape of the bottom, and available grade all matter.

Q = (1.486 / n) A R2/3 S1/2
U.S. customary units · R = area ÷ wetted perimeter

A is the wetted area in square feet; R is the hydraulic radius in feet; S is the energy slope as a fraction; and n is the Manning roughness coefficient. For sizing, the calculator takes S as the slope of the channel floor, which assumes the water surface runs parallel to it. The water level check in section 06 does not make that assumption.

A built-in channel slope and installation grade combine algebraically. A 0.7% channel installed on a surface falling 0.5% in the same direction has a 1.2% invert slope. Install that channel against a 1% rise and the effective slope becomes −0.3%; a uniform gravity-flow calculation cannot support that layout.

On a pre-sloped system, each channel has a place in the sequence. Its bottom gets deeper as water accumulates. The calculator checks the run at many stations and reserves the freeboard you select instead of treating a full-to-the-grate channel as the operating target.

For Dura Slope, the round bottom is modeled as a circular segment with straight walls above it. Hydraulic depth is measured below the underside of the grate; invert elevations referenced to its top include 0.75 in of grate thickness. Other families identify whether the section is documented or approximated; a nominal outside width is not a verified hydraulic width.

Where a manufacturer publishes a full-channel flow rate, as NDS does, the channel’s capacity is matched to that figure. The inside shape is then used to work out how much of that capacity the space kept clear under the grate takes away. For five NDS Pro Series lines the calculator uses the lower figure published by First Plast, the company that licenses those channel designs to NDS.

Reference: FHWA HEC-22 · open-channel and conduit hydraulics; each product's dimensional sources appear with its calculations.

Sizing the outlet and drain pipe

Peak discharge capacity is often the weak link in a drainage system. A long line of grates may admit water quickly, while the entire system drains through a single connection. Increasing the channel size does not automatically increase that connection's capacity.

Additional outlets can reduce the flow carried by downstream channel sections. Their benefit depends on location, the head of water available at each opening, and the connected pipes. If three outlets lead into one pipe, that shared pipe must still carry the combined discharge.

Outlet screen: Q = 0.62 Aoutlet √(2gH)
Pipe screen: Manning flow with A = πD²/4 and R = D/4

The outlet coefficient is an explicit screening assumption, not a product test rating. H is available head after the downstream water level is subtracted. Vertical end outlets are integrated across the submerged circular opening. Their elevation is an explicit assumption unless a source establishes it. The calculator checks this at the highest water level it allows in the channel and limits discharge to the smallest of three figures: what the opening can pass, what the branch pipe can carry, and the outlet flow rate the manufacturer publishes for that part, where there is one.

An outlet that needs more head than the water’s normal depth in the channel makes the water back up behind it. The checks in this section cannot show how far; the water level check in section 06 can. It also accounts for the length of each branch pipe, the entrance loss at each outlet, the drop into the shared pipe, the shared pipe itself and any standing water at its far end. Bends that are not entered and the wider drainage system beyond the pipe are not modelled.

Factory outlet positions vary by system. Some drains have a bottom connection in every section; some have connections only at specified sections; others discharge only at their ends. The parts schedule and model must respect those differences.

Water level check with EPA SWMM

The checks above each look at one thing: the grate, a point along the channel, an outlet, a pipe. They are quick, so the calculator runs them on every channel line to find the ones that can carry your peak flow with room to spare (at least 10%, or 25% where a channel’s inside shape is an estimate).

The system you select then goes through a fuller calculation, the water level check, which starts on its own. It uses the EPA's Storm Water Management Model (SWMM) to treat the channel, every outlet and the drain pipes as one connected system and solve for the water level along the whole run. That shows what separate checks cannot: water backing up behind an outlet, water running past one outlet to the next, and a pipe that cannot keep up.

SWMM does not replace the Rational Method here. The flow it is given is the same peak from section 02, held constant from an empty drain until the water levels stop changing. The check passes when all of that water leaves through the outlets and the water level keeps the clear space under the grate that you set. Before a result is shown, the run is repeated with the channel divided more finely and with a shorter time step, and the answers have to agree.

Engine: EPA SWMM 5.2.4, dynamic wave routing.

A complete trench drain: channel, grate, couplings and load rating

A complete trench drain needs a compatible grate, a supported outlet, sealed ends, and the correct connection and fastening details. A coupling is needed at an ordinary joint in systems such as Micro Channel, Slim Channel, Mini Channel and Spee-D. Pro Series, Dura Slope, and many commercial systems use integral joints instead. Included connectors and screws must be counted before additional hardware is added.

Load rating belongs to a specified installation, not to a grate in isolation. The channel and the grate are rated separately, and the calculator uses the lower of the two ratings. Frames, concrete encasement, support, fasteners, and where wheels cross the trench all affect the result. An ADA grate option also does not establish accessibility compliance for the whole site.

The schedule rounds your requested length into purchasable sections, shows the section sequence, and identifies the cut allowance. It separates documented catalog parts from items that still require confirmation. A cut through a channel's connection or a factory outlet may change the assembly; those details belong in the installation review.

The 3D view makes the layout easier to understand: the section order, the fall of the channel, and where water leaves. Once the water level check has run and passed its own accuracy tests, the blue surface is the water level it computed. The view is a steady snapshot. The engine holds peak inflow constant to let the network settle; that numerical experiment is not a storm hydrograph or a CFD calculation. Failed checks keep water-level results labeled as diagnostic.

Assumptions and sources

This calculator keeps numerical assumptions visible: rainfall provenance, runoff coefficients, added inflow, design allowance, roughness, freeboard, ponding, blockage, outlet head, and downstream pipe grade. Product references are attached to each family.

Version 3.0 · November 2026 · Water level check with EPA SWMM 5.2.4. Confirm site-specific design criteria before selecting an installation for construction.

Copyright © 2026 Drainage Connect. All rights reserved.